Log på Markedsindex.dk   
Opret blog   
Markedsindex.dk Markeder Butikker Debat Blogs
   Du er her: Markedsindex.dk -> Blogs -> Best Quality Embroidery -> The shuttle bed should be sprayed with white oil or anti-rust oil regularly
   
qualityembroiderys
 | 
Oprettet 15. January 2021 kl. 01:12
 | 
0 kommentarer
 | 
Tip en ven

The shuttle bed should be sprayed with white oil or anti-rust oil regularly

This is the basic maintenance of machinery. Less oil is added to the drive bottom bracket, which will wear the steel sleeve and bottom bracket between the drive rubber. If someone burns the motor coil, it is probably due to failure or disorder. The shuttle bed is generally adjusted and polished with sandpaper. For the Tajima machine, it should be noted that the cables behind the drive box should be tied to both sides, leaving a large space for ventilation.

The shuttle bed should be sprayed with white oil or anti-rust oil regularly. The place where the drive box has a fan is dusty. There is a lubrication hole on this one. In severe cases, the hole in the machine head base will wear out. Some thicker oil can be added to these places. X, Y-axis limit switch is not set properly, otherwise it will hit the frame and accelerate the damage of the small bearing. After that, the big and small connecting rods and the refueling between the silver arms will only accelerate the wear and cause loosening. It is recommended to add high-temperature bearing grease during overhaul at this place, so that it will not burn out. What is left is the flying saucer assembly.

Do not eject the floppy disk when the indicator light is on. Do not adjust the thermal relay on the motor casually. Dust removal and refueling are the most basic and most important. If it is normal, the motor coil will hardly burn out if it is protected. Otherwise, the thin copper and through holes on the circuit board will corrode. The most basic of computerized embroidery machines is maintenance. If the cooling fan is broken, it must be replaced immediately and the machine should be dusted regularly.

Because there is a needle bearing inside, it will cause the needle to loosen and wear if no lubrication is added. Use a blower to clean the inside regularly and pay attention to drying. When worn, the drive rubber will sway, the needle bar will shift, and there will be more chances for thread breakage. The floppy drive should be protected from dust. This is difficult to check. Sometimes the shuttle bed is very loud when the machine turns halfway, which is caused by the lack of oil in the shuttle bed. If you have a tape recorder, you should pay attention to plug and unplug the data cable when shutting down, otherwise the probability of burning the tape recorder is very high.

Attention should be paid to dust prevention in the circuit.As the staff of computer embroidery, we have certain knowledge of embroidery machine maintenance to greatly improve our position in the company. In more serious cases, the drive block and the bottom bracket are stuck, and the machine cannot be started. high speed embroidery machines Especially in summer, pay more attention to the heat dissipation of the X and Y drive boxes. If the needle bar box is less oiled, the lower hole of the presser foot and the needle bar will wear out more quickly. The needle bar box, the needle bar drive shaft, and the flying saucer assembly are the key places for refueling



0 kommentarer


Du skal være logget ind for at skrive en kommentar


Indtast brugernavn

*

Indtast password

*
 
Glemt dit password? Opret et login her

Best Quality Embroidery

Se mere om bloggeren qualityembroiderys

Lejia Electrical Machinery is a China embroidery machines manufacturers and commercial embroidery machines suppliers,offer best embroidery machines fo...

Gå til bloggen Best Quality Embroidery

Læs min blog


Seneste indlæg

Til blogindlæget The characteristics of embroidery needles are compared with sewing needles

The characteristics of em...

Twenty-five percent of the large, unique needle crown de...

Til blogindlæget The development trend of quilting technology

The development trend of ...

The development trend of quilting technology The market ...

Til blogindlæget The shuttle bed should be sprayed with white oil or anti-rust oil regularly

The shuttle bed should be...

This is the basic maintenance of machinery. Less oil is ...

Til blogindlæget The computerized embroidery machine has stronger memory capacity

The computerized embroide...

Compared with traditional embroidery machines, the compu...

Til blogindlæget Fully implement zero tariffs on products originating in Hong Kong and Macau.

Fully implement zero tari...

Recently, the Customs Tariff Commission of the State Cou...


Arkiv